Fox Crafting Studio
LightNews LightNews
foxcraftingstudio.bsky.social
Fox Crafting Studio
@foxcraftingstudio.bsky.social
230 followers 91 following 220 posts
Hobby wood worker since 2023.
I enjoy learning and trying out new techniques.
Feel free to give feedback and suggestions.
Posts Replies Media Videos
foxcraftingstudio.bsky.social
I practiced turning a hollow form. It is made from walnut. The wall got much thinner than I had initially planned, probably around 2 millimeters at the thinnest part.
The inner surface is still a bit rough, though, indicating the need for more practice ☺️
#woodworking #woodturning
Hollow form made from walnut. It is finished with walnut oil, polished, and waxed using carnauba wax. Side view. I choose the orientation of the wood such that the bright part is on top.
January 6, 2026 at 10:27 PM
foxcraftingstudio.bsky.social
A lidded box with a handle inspired by the Starfleet logo from Star Trek 💫

May the upcoming year 2026 be a successful year in your long and prosperous life! 🖖
#woodworking #woodturning
Lidded box made out of walnut with a handle made out of maple. Inside of the box.
December 30, 2025 at 3:58 PM
foxcraftingstudio.bsky.social
I wish you a festive season and a Merry Christmas! 🎄
Here are three snowmen I turned to join Richard Findley's festive turning challenge.
#woodworking #woodturning
Wooden snowmen, made from ash, maple, and pear (from left to right). The noses are made from padauk, the hat is dyed.
December 25, 2025 at 6:58 AM
foxcraftingstudio.bsky.social
Would you call it a bowl or a box? 😅
#woodworking #woodturning
A bowl with a box in the middle. The base is made out of wenge, the lid is made of zebrano and ebony. Bottom view of the bowl/box and the lid.
December 16, 2025 at 12:40 PM
foxcraftingstudio.bsky.social
Finally finished turning the wenge piece. Just the lid is still missing ... to be continued 😎
#woodworking #woodturning
A bowl with an integrated box. The wood is wenge. It is finished with walnut oil and wax.
December 9, 2025 at 10:03 PM
foxcraftingstudio.bsky.social
Oiling wood is always interesting, but the effect on this piece of wenge was truly amazing.
#woodworking #woodturning
Bottom site of a bowl made from wenge before oiling. Bottom site of a bowl made from wenge after oiling. I used walnut oil.
December 2, 2025 at 12:10 PM
foxcraftingstudio.bsky.social
Pushing towards the limits of my lathe 😁
#woodworking #woodturning
A blank of wenge on the lathe, which was still slightly too big even after cutting away the edges. I used a rasp to flatten the edges. The now fitting blank ready to be turned 😎
November 24, 2025 at 9:18 PM
foxcraftingstudio.bsky.social
This year's birthday presents were epic: some exciting wood blanks and a lovely handmade logo made from leather 😎
#woodworking #leather
Various wood blanks (e.g. wenge, zebrano, ebony, among others) and my logo made from leather. Such wonderful birthday presents. 🥰 Credits for the beautiful logo go to my brother.
November 17, 2025 at 9:18 PM
foxcraftingstudio.bsky.social
A little wooden bell made from mulberry wood.
#woodworking #woodturning
November 10, 2025 at 9:37 PM
foxcraftingstudio.bsky.social
I made my first vase from some lovely yew with a glass insert. 😎
#woodworking #woodturning
Putting a glass insert into a vase made from yew. Yew is such a lovely wood. I finished it with walnut oil and wax.
November 3, 2025 at 11:04 PM
foxcraftingstudio.bsky.social
The screw which fixes the indexing gear of my lathe became loose over time and disappeared somehow. I ordered a new screw. It was an interesting opportunity to learn about the inner parts of my lathe 😎
#woodturning
Inside of my lathe, where a screw is missing. This screw was supposed to fix the indexing gear. Inside of the lathe after adding a replacement screw.
October 16, 2025 at 9:21 PM
foxcraftingstudio.bsky.social
I was in a garden center today ... it turned out that the shape of the flowerpots can be quite intriguing for my inner woodturner 😁
October 11, 2025 at 8:37 PM
foxcraftingstudio.bsky.social
A small plate made from some lovely maple and with a rim colored using acrylic paint 😎
#woodworking #woodturning
October 8, 2025 at 3:24 PM
foxcraftingstudio.bsky.social
Some colorful experiments on the lathe using acrylic paint 🎨
#woodworking #woodturning
Painting acrylic paint on a round wooden piece before switching on the lathe. This silver coat was one of many coats I tried. After applying too much silver paint, I got desperate and just pushed the still wet paint around. Then, I sprayed some water while the piece was spinning. This led to a very fine texture, which finally pleased me enough to call it a day 😅
October 7, 2025 at 5:16 AM
foxcraftingstudio.bsky.social
This piece took me quite a while to make. It is made from oak, which I brushed, dyed and where I applied golden paste to highlight the grain.
#woodworking #woodturning
A square bowl made from oak. The outer part is dyed, the inner part shows the natural wood colors. Side view. I sanded the rim such that the oak colors are visible there as well.
October 2, 2025 at 9:33 AM
foxcraftingstudio.bsky.social
Once it was the leg of a cabinet used by my great-grandma. Then, it was left to rot for decades. But now it is reborn as a wooden bell 😎
#woodworking #woodturning
September 16, 2025 at 2:38 PM
foxcraftingstudio.bsky.social
I charred the surface of this bowl made from oak. Did I make it better or worse? 😅
#woodworking #woodturning
Charring the bowl using a blowtorch. Brushing the surface. This created an interesting texture with deep rills. Surface after applying hard wax oil. The shine is pretty nice, especially in bright sunlight. The edge with the end grain got an interesting rough structure.
September 3, 2025 at 7:31 AM
foxcraftingstudio.bsky.social
The third (and last) bowl I made recently from some alder wood. I am starting to wonder what I should do with all these bowls 😅
#woodworking #woodturning
Top view. I undercut the rim, which turned out very challenging. I need more practice with that... Bottom view of the bowl, showing the recess used to fix the bowl on the lathe.
August 28, 2025 at 5:26 PM
foxcraftingstudio.bsky.social
Here is another bowl I made last week during a workshop: Alder wood with a burned rim, this time with a bit more unusual design.
#woodworking #woodturning
Lathe with the bowl still attached. Lots of beautiful wooden shavings were produced during the course 😅 Top view of the bowl. The rim was first burned with a blowtorch. Later, small grooves were cut with the skew. Bottom view of the bowl.
August 24, 2025 at 9:51 PM
foxcraftingstudio.bsky.social
Last weekend I joined a two-day wood turning workshop about turning bowls. Here is the first bowl I finished there. The dark rim was made using a blowtorch, which is an interesting and yet easy-to-make design element.
#woodworking #woodturning
Bowl made from alder wood. A dark rim was made using a blowtorch, followed by some brushing. The bottom of the bowl.
August 22, 2025 at 8:33 AM
foxcraftingstudio.bsky.social
I made another small square bowl. I feel like these small bowls are a nice and fun way to practice some wood turning.
#woodworking #woodturning
August 13, 2025 at 2:55 PM
foxcraftingstudio.bsky.social
I recently finished this square bowl made from some lovely oak. I tried hard wax oil as a finish for the first time, and I am quite satisfied with the result.
#woodworking #woodturning
Square bowl before applying the finish. The bowl just after applying the first coat of hard wax oil, and before removing the excess. I applied two coats in total. The used hard wax oil is from the company PNZ. The finished bowl under natural lighting conditions. After letting the hard wax oil dry, I polished the surface slightly with some cloth, which slightly increased the shine. The finished bowl tilted slightly differently.
August 7, 2025 at 6:33 AM
foxcraftingstudio.bsky.social
Woodturning is cool 😎
#woodworking #woodturning
July 31, 2025 at 6:18 AM
foxcraftingstudio.bsky.social
I made a bowl from robinia using black dye and gold paste on the outside to highlight the exciting grain patterns. 😎
#woodworking #woodturning
Side view of the bowl. I first brushed the wood, then dyed it and later applied the gold paste. After that, I removed the excess of the gold paste, leading to the nice contrast between gold and black. Another side view from another angle. I finished the bowl using walnut oil and wax. View into the inside of the bowl, where you can see the natural color of the robinia. Another view from the top. I am pretty sure I will reuse this technique again 😀
July 22, 2025 at 5:42 PM
foxcraftingstudio.bsky.social
I bought a 5 centimeter Forstner bit. It felt like using a lightsaber when drilling into this piece of robinia 😁
#woodworking #woodturning
July 17, 2025 at 6:21 AM