Enigma the Creator
@enigmathecreator.bsky.social
Engineer, gamer, designer/creator. Former homebrewer, forever whiskey lover. General collector of hobbies...
https://linktr.ee/EnigmaWorkshop
https://enigmaworkshop.etsy.com
https://linktr.ee/EnigmaWorkshop
https://enigmaworkshop.etsy.com
Microphones:
www.amazon.com/dp/B00X7BN98Y
Microphone amp board:
www.amazon.com/dp/B083YWT5W3
Headphone amp board:
www.amazon.com/dp/BO8FCH2C1X
Headphone speakers:
www.amazon.com/dp/BODKDYSRKQ
www.amazon.com/dp/B00X7BN98Y
Microphone amp board:
www.amazon.com/dp/B083YWT5W3
Headphone amp board:
www.amazon.com/dp/BO8FCH2C1X
Headphone speakers:
www.amazon.com/dp/BODKDYSRKQ
uxcell 10pcs 6mm x 3.5mm Mini Electret Microphone Condenser Pickup w Lead
It is back electret type, with high resistance to vabratens, high signal to noise rate.Widely used in the cassette recorder, wireless microphone and voice control circuits.
www.amazon.com
July 9, 2025 at 11:56 PM
Microphones:
www.amazon.com/dp/B00X7BN98Y
Microphone amp board:
www.amazon.com/dp/B083YWT5W3
Headphone amp board:
www.amazon.com/dp/BO8FCH2C1X
Headphone speakers:
www.amazon.com/dp/BODKDYSRKQ
www.amazon.com/dp/B00X7BN98Y
Microphone amp board:
www.amazon.com/dp/B083YWT5W3
Headphone amp board:
www.amazon.com/dp/BO8FCH2C1X
Headphone speakers:
www.amazon.com/dp/BODKDYSRKQ
Not going to lie, I have looked at active cooling systems to install in a jetpack!
July 8, 2025 at 5:58 PM
Not going to lie, I have looked at active cooling systems to install in a jetpack!
Thanks! Still a lot left to do, but I'm happy with it as a start!
July 7, 2025 at 3:35 AM
Thanks! Still a lot left to do, but I'm happy with it as a start!
Printability issues*
July 6, 2025 at 12:48 AM
Printability issues*
Out of curiosity, how would you approach a PB&J sandwich?
June 30, 2025 at 11:56 AM
Out of curiosity, how would you approach a PB&J sandwich?
Very situational, but it's super useful when the need arises
June 30, 2025 at 11:10 AM
Very situational, but it's super useful when the need arises
Nope! Less noxious and easier to work with than printer resins, including less processing. Just need to make sure it cures well and then sand it.
I didn't use for snoring the whole piece, just where you get more have later steps on shallow angles or the new you get on large supported surfaces.
I didn't use for snoring the whole piece, just where you get more have later steps on shallow angles or the new you get on large supported surfaces.
June 28, 2025 at 3:28 PM
Nope! Less noxious and easier to work with than printer resins, including less processing. Just need to make sure it cures well and then sand it.
I didn't use for snoring the whole piece, just where you get more have later steps on shallow angles or the new you get on large supported surfaces.
I didn't use for snoring the whole piece, just where you get more have later steps on shallow angles or the new you get on large supported surfaces.