Vengeful Wraith
@vengefulwraith1.bsky.social
Writer, inventor, artist, and local ghost.
Main engine assembled! Now for accessories and some 3D scanning.
December 23, 2025 at 6:13 PM
Main engine assembled! Now for accessories and some 3D scanning.
Mis-using a tool to get the job done? Just a Tuesday.
December 23, 2025 at 6:11 PM
Mis-using a tool to get the job done? Just a Tuesday.
Installing poppet valves is annoying. But! It is done.
December 23, 2025 at 6:08 PM
Installing poppet valves is annoying. But! It is done.
Things be spinning!
December 18, 2025 at 7:48 AM
Things be spinning!
Compressing and inserting all mated pairs of pistons.
December 18, 2025 at 6:09 AM
Compressing and inserting all mated pairs of pistons.
Checking ring gap. Everything looks good!
December 18, 2025 at 6:08 AM
Checking ring gap. Everything looks good!
Rrrrrotating maaass.
December 18, 2025 at 12:17 AM
Rrrrrotating maaass.
Torqued all main caps and gauge checked. The squish is on the higher end, but still under the max width of 2 thou.
December 17, 2025 at 11:02 PM
Torqued all main caps and gauge checked. The squish is on the higher end, but still under the max width of 2 thou.
ARP studs in for the bottom end!
December 17, 2025 at 11:01 PM
ARP studs in for the bottom end!
Reposted by Vengeful Wraith
So ... bullying works!
In France we are not kidding with the nonsense some companies does on us and seeing the huge visibility they got from the animation, they realized the mistake
I hope this can work on other countries as well
Might cost me my account to say that but "keep bullying companies!"
In France we are not kidding with the nonsense some companies does on us and seeing the huge visibility they got from the animation, they realized the mistake
I hope this can work on other countries as well
Might cost me my account to say that but "keep bullying companies!"
December 17, 2025 at 7:38 PM
So ... bullying works!
In France we are not kidding with the nonsense some companies does on us and seeing the huge visibility they got from the animation, they realized the mistake
I hope this can work on other countries as well
Might cost me my account to say that but "keep bullying companies!"
In France we are not kidding with the nonsense some companies does on us and seeing the huge visibility they got from the animation, they realized the mistake
I hope this can work on other countries as well
Might cost me my account to say that but "keep bullying companies!"
Saw a post in the Fusion 360 subreddit about creating a similar design. My boyfriend watched me for about an hour and half to make up the file and then an overnight print run.
December 16, 2025 at 4:50 AM
Saw a post in the Fusion 360 subreddit about creating a similar design. My boyfriend watched me for about an hour and half to make up the file and then an overnight print run.
Replacing all the main bearings.
December 13, 2025 at 6:07 PM
Replacing all the main bearings.
New bearings pressed in.
December 12, 2025 at 4:31 AM
New bearings pressed in.
And it starts with removing and seating the new cam bearings in place.
December 12, 2025 at 12:33 AM
And it starts with removing and seating the new cam bearings in place.
Getting closer to being done with the roll cage. It'll technically be a 9 point system by the time it's finished.
December 11, 2025 at 10:06 PM
Getting closer to being done with the roll cage. It'll technically be a 9 point system by the time it's finished.
The army grows. I've figured out how to mix the resin with less bubbles. The top ones I may not end up using, but we'll see.
December 11, 2025 at 10:05 PM
The army grows. I've figured out how to mix the resin with less bubbles. The top ones I may not end up using, but we'll see.
Designed molds for the new 4 link bushings. The rubber is a 1:1 ratio and cures to 80 durometer. Much stiffer than OEM.
December 11, 2025 at 10:01 PM
Designed molds for the new 4 link bushings. The rubber is a 1:1 ratio and cures to 80 durometer. Much stiffer than OEM.
Set back with the build. All 10 urethane bushings for the triangulated 4 link suspension have turned to dust. This due to piss poor manufacturing. So, I'm going to be engineering my own.
December 11, 2025 at 10:00 PM
Set back with the build. All 10 urethane bushings for the triangulated 4 link suspension have turned to dust. This due to piss poor manufacturing. So, I'm going to be engineering my own.
Starting a multi-year project for creating a Copper Acetate crystal art piece.
December 10, 2025 at 12:34 AM
Starting a multi-year project for creating a Copper Acetate crystal art piece.
Did you know I'm writing a book series? I'm 85% done writing my second book now!
December 7, 2025 at 12:09 AM
Did you know I'm writing a book series? I'm 85% done writing my second book now!
Someone help me understand why my ding dong of a boyfriend is coating his underwear in automotive rubber undercoating.
December 5, 2025 at 1:50 AM
Someone help me understand why my ding dong of a boyfriend is coating his underwear in automotive rubber undercoating.
I like em thick, stroked, blown, and excited, and preferably 8 at a time
November 29, 2025 at 1:17 AM
I like em thick, stroked, blown, and excited, and preferably 8 at a time
One whole MAN power
November 27, 2025 at 9:45 PM
One whole MAN power
Established the harness bar location. I have a solid game plan for properly finishing the roll cage now.
November 27, 2025 at 5:16 PM
Established the harness bar location. I have a solid game plan for properly finishing the roll cage now.